French-fry cutter transforms entire potatoes into consummately cut fries in only a second. Basically load up with a potato, sweet potato, or other bland vegetable and press down on the handle to compel nourishment through the hardened steel cutting edges for course reading cafe quality fries.​

Open the machine, unscrew the handle at the front and lift up until the container is completely lying back on its pivots. Check the rotor by hand to guarantee that it is totally allowed to pivot and that the blade square get together is appropriately in position and verified by the two fixing nuts. Close the top and fix the nut. It is presently protected to control the machine on. To begin the Commercial French Fry Cutter Potato Slicer machine, press the green catch at the front, and to stop, press the red catch. The machine is set to have a 10-minute run time, trailed by a 5-minute rest period. There is a worked in clock that determination off the machine following 10 minutes. Continuously enable it to chill off for 5 minutes before working it once more.

Heavy duty French fries cutter machine are machines that anybody can use easily. For the best outcomes, it is significant on the off chance that you are familiar with the working of a potato slicer. When you realize how to utilize the machine, at that point you will have a simple time when cutting potatoes. Commercial French Fry Cutter Potato Slicer automatic has a funnel-shaped tube where you pour your potatoes. The potatoes at that point slide down the chute and they are adjusted the long way. With the assistance of a rotating paddle or s disk, the potatoes go through a stationary blade which cuts a section the length and width of the potato. It includes a lot of rotating blades that are made of great hardened steel which holds a sharp front line as well as gives the unit an all-encompassing life. The moving piece of the unit is all around mounted on a pole that pivots in a metal roller. You simply need to utilize some eatable oil every now and then for lubrication.​

Lay each half cut-side down. Slice lengthwise into 1/4 to 1/2 inch thick slices. Stack about half of the slices and cut lengthwise into 1/4 to 1/2 inch thick fries. Repeat with the rest. Perfect French Fries. Tip: The potatoes must be completely dry before frying.​

Neutral tasting oils are incredible for browning: shelled nut, canola, vegetable, safflower, grape-seed, and so forth. These all have a smoke point well above 350°F. A few oils, similar to corn, coconut and sesame, have smoke focuses past 350°F, Commercial French fry cutter potato slicer machine however they confer a great deal of flavor into the completed item that you might possibly need.

• New Star 42313. Boasting a durable stainless-steel design, suction feet and ½-inch blades, this French fry cutter is one of the best on the market.

• Mandolin Food Slicer. This French fry cutter is extremely simple to use, versatile, and sharp.

• Savant Kitchen Easy Grip Slicer.

• Weston Products French fry Cutter.

​

1. Keep fingers clear of cutting blade when operating or cleaning. Never leave the French fry cutter unattended, especially around children. Use caution when assembling and disassembling.

2. Check French fries cutter commercial for any visual damage that may have happened in shipment.

3. Then wash potato French fries machine prior to use with a mild dish detergent and warm water. Use a soft bristle brush if necessary.

4. Install French fry Cutter handle using large bolt, nut, and washer.

5. Install French fry Cutter handle push rods into handle support

6. Tighten, attaching hardware so they are snug. Do not over tighten!

7. The French fry Cutter can be mounted on flat table or a wall. For best use, secure the unit to a solid surface only.

8. This French fry Cutter is not intended to cut bones, fish, meats or frozen vegetables.​

1. Utilize a mild cleanser and warm water. A delicate fiber brush might be utilized if essential. Handle shouldn't be evacuated for cleaning.

2. Use alert when dismantling the French fry slicer pusher and square. Blades are sharp.

3. Extricate the three wing nuts verifying the square on the front of French fries machine.

4. Extricate the two set screws behind the pusher and move pusher handle back. The pusher close will fall off. Clean with a delicate brush or appropriate contraption. Commercial French Fry Cutter Potato Slicer machine Try not to use your fingers as blades are sharp. Clean and altogether dry to guarantee a dependable utilization of this commercial French Fry Cutter machine.​

• Commercial French fry cutter restaurant is cost-effective and economical

• You can use it to slice different shapes like straight or round

• It does not waste food because the whole potato is used

• Easy to operate and does not consume a lot of time

• It is made of sturdy materials like aluminum or stainless steel for durability​

Commercial French Fry Cutter Potato Slicer automatic are ideal for restaurants, cafes that do heaps of French fries each day. High volume restaurants, central kitchens for healthcare campuses, colleges, canteens and schools can profit by these efficient units. They utilize electrical power to drive potatoes through the cutting sharp edges, lessening strain on the operator.

Manual French fry cutters let you cut potatoes into straight fries, wedge fries, and claim to fame cut fries with the utilization of a manual switch or handle. Perfect for snack bars, cafes, and bistros, manual fry cutters are more affordable so they are an extraordinary decision for independent companies or new companies.​

If you want to change the style or size of your fries of your fries without purchasing a totally different unit, you can! By blending the right blade set and push block from your fry cutter's maker you can change a 1/4" straight cutter to a 6 wedge cutter or pretty much some other accessible cut type. Some blade edge sets and push squares are now bundled together as sets to guarantee that you get the right parts! Simply recollect blades and push blocks from one producer won't take a shot at another organization's french fry cutter. For instance, on the off chance that you wish to change the cut sort on a Vollrath fry cutter, you should buy a Vollrath sharp blade set and push block.​

Having stock or not and comparing to the world market, this products price can be up & down. But right now, Commercial French Fry Cutter Potato Slicer machine starting cost is 8,500 Taka price in Bangladesh. If you want to buy, the price can be up & down depending on the feature, specification and other customization.​